Herzlich Willkommen auf Hygiene-shop.eu! ➽ Rabattaktionen & Gutscheine

Angled two-wall grab bar available in 2 varaints of satin brushed stainless steel

Bobrick B- 68137 / .99 Two-Wall Tub/Shower Toilet Compartment Grab Bar Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1⁄8" (3mm) thick, type 304 stainless steel plate, 2" W x 3 1⁄8" H (50 x 80mm), with screw holes for concealed anchors. Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1⁄4" (85mm) diameter. Cover snaps over mounting flange to conceal screws.

Hoeveelheid Basisprijs
tot 1 € 191,52 * € 191,52 * / 1 Stuk(s)
vanaf 2 € 181,95 * € 181,95 * / 1 Stuk(s)
vanaf 4 € 176,20 * € 176,20 * / 1 Stuk(s)
vanaf 6 € 172,37 * € 172,37 * / 1 Stuk(s)
Inhoud: 1 Stuk(s)

Prijzen incl. btw excl. verzendingskosten

Levertijd in 6-10 werkdagen

Uitvoering:




Angebot anfordern ab einem Gesamt-Warenkorb-Wert von (sonst zur Kasse): € 150,00

Offerte aanvragen
  • BR000147-1
  • Bobrick
  • 9009817015222
WebwinkelKeur Webwinkel Keurmerk
Bobrick two-wall tub / shower toilet compartment grab bar available in 2 variants Provide...meer

Bobrick two-wall tub / shower toilet compartment grab bar available in 2 variants

Bobrick two-wall tub / shower toilet compartment grab bar available in 2 variants

Provide concealed anchor device or backing as specified or required in accordance with local building codes before wall is finished. Fasten concealed mounting flanges to anchor device or backing with at least two screws opposing each other in each flange. Snap flange covers over each mounting flange to conceal mounting screws. Concealed anchor devices and mounting screws are not included with Bobrick grab bars and must be specified as an accessory. For Grab Bars with an Intermediate Flange(s), Pull Snap-Flange Covers away from mounting flanges. Place grab bar in desired mounting location. Use intermediate flange as a template to mark location of mounting screws at intermediate flange only. Mark screw locations at the center of the slot in the middle of the double-keyhole shaped mounting holes (2) in the intermediate flange. Remove grab bar from wall. Drive the intermediate flange mounting screws into wall at marked locations. Note: Make sure to leave a space of just over 1/8'' (3.17mm) between the underside of the screw head and the wall. Install grab bar on the wall by placing the round ends of the intermediate flange double-keyhole shaped mounting holes over the mounting screws (2) are located in the middle of the flange slots. Install the mounting screws into the wall at the end flanges and secure tightly. Tighten the mounting screws at the intermediate flange. Press all snap-flange covers into place to conceal mounting flanges.

- Grab bar shall be type-304 stainless steel with satin-finish.
- Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/2" (38mm) outside diameter.
- Clearance between the grab bar and wall shall be 1-1/2" (38mm).
- Concealed mounting flanges shall be 11-gauge (3.2mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with at least two screw holes for attachment to wall.
- Flange covers shall be 22 gauge (0.8mm), 3-1/4" (85mm) diameter x 1/2" (13mm) deep, and shall snap over mounting flange to conceal mounting screws and/or WingIt fasteners.
- Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit.
- Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.

Abmessungen:
Breite: 915 mm
Länge: 1370 mm
Durchmesser: 38 mm

B-68137 - Not Irradiated​
B-68137.99 - Peened

Data sheet


Specificaties:

  • - Grab bar shall be type-304 stainless steel with satin-finish.
  • - Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/2" (38mm) outside diameter.
  • - Clearance between the grab bar and wall shall be 1-1/2" (38mm).
  • - Concealed mounting flanges shall be 11-gauge (3.2mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with at least two screw holes for attachment to wall.
  • - Flange covers shall be 22 gauge (0.8mm), 3-1/4" (85mm) diameter x 1/2" (13mm) deep, and shall snap over mounting flange to conceal mounting screws and/or WingIt fasteners.
  • - Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit.
  • - Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.

Verdere links naar "Bobrick two-wall tub / shower toilet compartment grab bar available in 2 variants"
Laatst bekeken
WhatsApp Chat Support
Hygiene-shop.nl WhatsApp Support
WhatsApp Chat Support
Hallo! Hoe kunnen wij u helpen?
Welcome at our shop! Outside our opening hours it might take a little bit longer until we answer yourinquiry.
whatspp icon whatspp icon