Complies with Planning Guide for Accessibles Restrooms. Seat is constructed of durable, water-resistant, ivory-colored 1⁄2" (13mm) thick solid phenolic. Reversible for left- or right-hand field installation. Frame and mounting brackets are type 304 stainless steel with self-locking mechanism. Supports up to 360 lbs (163 kg) when properly installed. Seat 33" (840mm) wide, projects 22 5⁄16" (565mm) from wall. SAFETY WARNING: Shower seats are no stronger than the anchors and walls to which they are attached and must be firmly secured in order to support the loads for which they are intended.
Hoeveelheid | Basisprijs | |
---|---|---|
tot 1 | € 642,57 * | € 642,57 * / 1 Stuk(s) |
vanaf 2 | € 610,44 * | € 610,44 * / 1 Stuk(s) |
vanaf 4 | € 591,16 * | € 591,16 * / 1 Stuk(s) |
vanaf 6 | € 578,31 * | € 578,31 * / 1 Stuk(s) |
Prijzen incl. btw excl. verzendingskosten
Levertijd in 6-10 werkdagen
- Artikelnr.: BR000137
-
Fabrikant: Bobrick
Bobrick B-5181 Reversible Folding Shower Seat for surface mounting load up to 136kg
Bobrick B-5181 Reversible Folding Shower Seat for surface mounting load up to 136kg
CAUTION NOTE: L-shaped folding shower seat, when properly installed and maintained, has sufficient strength to support a single user up to a maximum static load of 360 lbs (163 kg). In the interests of safety and the protection of end users, this seat should not be used to support weights exceeding 360 lbs (163 kg). Failure to abide by this warning may result in seat malfunctioning, potentially causing minor to moderste injury. TOTAL WEIGHT ON SEAT MUST NOT EXCEED 360 LBS (163 KG).
Shower seat folds up against wall when not in use. The spring at the top of the baseplate holds seat in upright position until released by pulling the top of the seat away from the wall. Mounting flanges and guide bracket allow for varying mounting heights and leave the floor clear for easy cleaning. Nonporous solid phenolic seat has slots to permit water to drain, does not splinter or require oiling, and will not support growth of bacteria. Slotless round-head carriage bolts and acorn nuts provide additional safety to user. Bobrick shower seats, when properly installed, have sufficient strength to support 360 lbs., (163 kg) complying with accessible design guidelines (including ADAAG in the U.S.A.).
Dimensions:
width: 840 mm
height: 565 mm
typical mounting height: 430 - 485 mm
SAFETY WARNING: Shower seats are no stronger than the anchors and walls to which they are attached and must be firmly secured in order to support the loads for which they are intended. Consult and comply with local building codes. To avoid potential injury, the building owner or maintenance personnel should remove the shower seat from service if the shower seat is not adequately secured to the wall. Unit shall support static loads of up to 360 lbs (163 kg) when properly installed and used. To avoid potential seat malfunction, DO NOT use seat if weight exceeds 360 lbs (163 kg).
- Reversible folding shower seat shall have a frame constructed of type-304, satin-finish stainless steel that consists of 16-gauge (1.6mm), 1-1/4'' (30mm) square tubing and 18-gauge (1.2mm), 1'' (25mm) diameter seamless tubing. S
- Seat shall be one-piece, 1/2" (13mm) thick, solid phenolic with matte-finish, antique white-colored, melamine surfaces, and black phenolic-resin core; secured to frame with stainless steel carriage bolts and acorn nuts.
- Seat shall be reversible for left- or right-hand installation in the field.
- Shower seat shall be equipped with two 3'' (75mm) diameter mounting flanges constructed of type-304, 3/16'' (5mm) thick, satin-finish stainless steel; a guide bracket constructed of type-304, 16-gauge (1.6mm), satin-finish stainless steel; and a spring constructed of type-301, 24-gauge (0.6mm) stainless steel that is spot-welded to a baseplate of type-304, heavygauge stainless steel.
- Seat shall remain in upright position when not in use. Shower seat shall comply with accessible design guidelines (including ADAAG in the U.S.A.).
Data sheet
Specificaties:
- Dimensions: width: 840 mm height: 565 mm
- typical mounting height: 430 - 485 mm
- Reversible folding shower seat shall have a frame constructed of type-304, satin-finish stainless steel that consists of 16-gauge (1.6mm), 1-1/4'' (30mm) square tubing and 18-gauge (1.2mm), 1'' (25mm) diameter seamless tubing. S
- Seat shall be one-piece, 1/2" (13mm) thick, solid phenolic with matte-finish, antique white-colored, melamine surfaces, and black phenolic-resin core; secured to frame with stainless steel carriage bolts and acorn nuts.
- Seat shall be reversible for left- or right-hand installation in the field.
- Shower seat shall be equipped with two 3'' (75mm) diameter mounting flanges constructed of type-304, 3/16'' (5mm) thick, satin-finish stainless steel; a guide bracket constructed of type-304, 16-gauge (1.6mm), satin-finish stainless steel; and a spring constructed of type-301, 24-gauge (0.6mm) stainless steel that is spot-welded to a baseplate of type-304, heavygauge stainless steel.
- Seat shall remain in upright position when not in use. Shower seat shall comply with accessible design guidelines (including ADAAG in the U.S.A.).