Bobrick stainless steel 90° grab bar loadable with 408kg for bath- sanitary area
Satin polished stainless steel grap bar bathtub, shower or toilet area. Available with gripping surface or with normal execution. Can be loaded with up to 408kg when properly installed.
| Hoeveelheid | Prijs per eenheid |
|---|---|
| Tot 1 |
€ 163,00
|
| Vanaf 2 |
€ 160,75
|
| Vanaf 3 |
€ 158,50
|
| Vanaf 4 |
€ 156,25
|
| Vanaf 5 |
€ 154,00
|
| Vanaf 6 |
€ 151,80
|
| Vanaf 8 |
€ 149,55
|
| Vanaf 10 |
€ 147,30
|
voor levering naar Niederlande.
Beschikbaar, Levertijd 10-14 werkdagen
55 Goswell Road 1st Floor Clerkenwell
EC1V 7EN London
Vereinigtes Königreich
euoffice@bobrick.com
Herbert Place 25
D02 AY86 Dublin
Irland
Telephone: +44 (0) 1793 78 45 45
euoffice@bobrick.com
Bobrick grab bar loadable with 408 kg stainless steel 90° for bath and toilet area
Bobrick grab bars that provide 1-1/2" (38mm) clearance from wall can support loads in excess of 900 pounds (408kg) if properly installed. Other grab bar configurations can support loads in excess of 250 pounds (113kg) if properly installed, complying with accessible design (including ADAAG in the U.S.A.) for structural strength.
Safety Warning: Grab bars are no stronger than the anchors and walls to which they are attached and, therefore, must be firmly secured in order to support the loads for which they are intended. To avoid potential injury, the building owner or maintenance personnel should remove the grab bar from service if the grab bar is not adequately secured to wall or if there is any observed damage to the welds.
- Grab bar shall be type-304 stainless steel with satin-finish.
- Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/4" (32mm) outside diameter.
- Clearance between the grab bar and wall shall be 1-1/2" (38mm).
- Concealed mounting flanges shall be 1/8" (3mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with two screw holes for attachment to wall.
- Flange covers shall be 22-gauge (0.8mm) stainless steel, 3-1/4" (85mm) diameter, and shall snap over mounting flanges to conceal mounting screws and/or WingIt fasteners.
- Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit.
- Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.
Data:
- Dimensions: Ø32mm - L: 915mm - B: 610
- Material: satin polished stainless steel
- Mounting material not included in delivery in delivery.
- Loadable with 408kg
- meets the guidelines for disabled
Data sheet (English)
- Dimensions: Ø32mm - L: 915mm - B: 610
- Material: satin polished stainless steel 18/10 (1.4301)
- Mounting material not included in delivery in delivery.
- Loadable with 408kg
- meets the guidelines for disabled
- Eindflenzen 50 x 80 mm 3 mm dik;
- met twee gaten voor bevestiging aan de wand.
- Tussenflenzen 65 x 80 mm breed, 80 mm diameter.
- Flens dekt roestvrij staal CrNi 18/10 (1.4301), 0,8 mm dik, satijn afwerking. 85 mm diameter x 13 mm diepte.
Ähnliche Artikel
