Beste Klanten & Zakelijke Partners!
Hartelijk welkom bij de Hygiene-shop.nl!
Op onze pagina actuele informatie houden wij u op de hoogte van alle nieuwtjes & actualiteiten.
Wij wensen iedereen gezondheid toe in deze aparte tijden!

Straight Bobrick grab bar of satin brushed stainless steel with peened finish

Bobrick B-6806.99 Straight Grab Bar Peened 36" (915mm) long, 1-1/2" (38mm) dia. tubing, peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1⁄8" (3mm) thick, type 304 stainless steel plate, 2" W x 3 1⁄8" H (50 x 80mm), with screw holes for concealed anchors. Cover is 22-gauge (0.8mm), type 304 stainless steel with satin finish, 3 1⁄4" (85mm) diameter. Cover snaps over mounting flange to conceal screws.

Hoeveelheid Basisprijs
tot 1 € 67,76 * € 67,76 * / 1 Stuk(s)
vanaf 2 € 64,37 * € 64,37 * / 1 Stuk(s)
vanaf 4 € 62,34 * € 62,34 * / 1 Stuk(s)
vanaf 6 € 60,98 * € 60,98 * / 1 Stuk(s)
Inhoud: 1 Stuk(s)

Prijzen incl. btw excl. verzendingskosten

Levertijd in 6-11 werkdagen

Formaat:

Offerte aanvragen
  • BR000144-5
  • Bobrick
  • 9009817045519
WebwinkelKeur Webwinkel Keurmerk
Bobrick B-6806.99 straight grab bar peened of satin brushed stainless steel Provide...meer
Productinformatie "Straight Bobrick grab bar of satin brushed stainless steel with peened finish"

Bobrick B-6806.99 straight grab bar peened of satin brushed stainless steel

Provide concealed anchor device or backing as specified or required in accordance with local building codes before wall is finished. Fasten concealed mounting flanges to anchor device or backing with at least two screws opposing each other in each flange. Snap flange covers over each mounting flange to conceal mounting screws. Concealed anchor devices and mounting screws are not included with Bobrick grab bars and must be specified as an accessory. For Grab Bars with an Intermediate Flange(s), Pull Snap-Flange Covers away from mounting flanges. Place grab bar in desired mounting location. Use intermediate flange as a template to mark location of mounting screws at intermediate flange only. Mark screw locations at the center of the slot in the middle of the double-keyhole shaped mounting holes (2) in the intermediate flange. Remove grab bar from wall. Drive the intermediate flange mounting screws into wall at marked locations. Note: Make sure to leave a space of just over 1/8'' (3.17mm) between the underside of the screw head and the wall. Install grab bar on the wall by placing the round ends of the intermediate flange double-keyhole shaped mounting holes over the mounting screws (2) are located in the middle of the flange slots. Install the mounting screws into the wall at the end flanges and secure tightly. Tighten the mounting screws at the intermediate flange. Press all snap-flange covers into place to conceal mounting flanges.

Safety Warning: Grab bars are no stronger than the anchors and walls to which they are attached and, therefore, must be firmly secured in order to support the loads for which they are intended. To avoid potential injury, the building owner or maintenance personnel should remove the grab bar from service if the grab bar is not adequately secured to wall or if there is any observed damage to the welds.

- Grab bar shall be type-304 stainless steel with satin-finish.
- Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/2" (38mm) outside diameter.
- Clearance between the grab bar and wall shall be 1-1/2" (38mm).
- Concealed mounting flanges shall be 11-gauge (3.2mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with at least two screw holes for attachment to wall.
- Flange covers shall be 22 gauge (0.8mm), 3-1/4" (85mm) diameter x 1/2" (13mm) deep, and shall snap over mounting flange to conceal mounting screws and/or WingIt fasteners.
- Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit.
- Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.

Diameter of Grab bar: 38 mm
B-6806.99x18 - 18" (455mm) long
​B-6806.99x24 - 24" (610mm) long
B-6806.99x30 - 30" (760mm) long
B-6806.99x36 - 36" (915mm) long
B-6806.99x42 - 42" (1065mm) long

Data sheet


Technische Daten:

  • Diameter of Grab bar: 38 mm
  • Grab bar shall be type-304 stainless steel with satin-finish.
  • Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/2" (38mm) outside diameter.
  • Clearance between the grab bar and wall shall be 1-1/2" (38mm).
  • Concealed mounting flanges shall be 11-gauge (3.2mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with at least two screw holes for attachment to wall.
  • Flange covers shall be 22 gauge (0.8mm), 3-1/4" (85mm) diameter x 1/2" (13mm) deep, and shall snap over mounting flange to conceal mounting screws and/or WingIt fasteners.
  • Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit.
  • Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.

Montage: Wandmontage
Materiaal: RVS
Sanitair inrichting: Handsteunen & Leuningen
Kleuren: Geborsteld RVS
Verdere links naar "Straight Bobrick grab bar of satin brushed stainless steel with peened finish"
Laatst bekeken