Beste Klanten & Zakelijke Partners!
Hartelijk welkom bij de Hygiene-shop.nl!
Op onze pagina actuele informatie houden wij u op de hoogte van alle nieuwtjes & actualiteiten.
Wij wensen iedereen gezondheid toe in deze aparte tijden!

Straight Bobrick grab bar peened of satin finish stainless steel in different legths

Bobrick B-5806.99 straight grab bar preened of satin brushed stainless steel with concealed mounting for bathtub, shower- or toilet area.

Hoeveelheid Basisprijs
tot 1 € 54,45 * € 54,45 * / 1 Stuk(s)
vanaf 2 € 51,73 * € 51,73 * / 1 Stuk(s)
vanaf 4 € 50,09 * € 50,09 * / 1 Stuk(s)
vanaf 6 € 49,01 * € 49,01 * / 1 Stuk(s)
Inhoud: 1 Stuk(s)

Prijzen incl. btw excl. verzendingskosten

Levertijd in 6-11 werkdagen

Formaat:

Offerte aanvragen
  • BR000149-1
  • Bobrick
WebwinkelKeur Webwinkel Keurmerk
Bobrick B-5806.99 straight grab bar peened of stainless steel for shower and bath Bobrick...meer
Productinformatie "Straight Bobrick grab bar peened of satin finish stainless steel in different legths"

Bobrick B-5806.99 straight grab bar peened of stainless steel for shower and bath

Bobrick grab bars that provide 1-1/2" (38mm) clearance from wall can support loads in excess of 900 pounds (408kg) if properly installed. Other grab bar configurations can support loads in excess of 250 pounds (113kg) if properly installed, complying with accessible design (including ADAAG in the U.S.A.) for structural strength.

Provide concealed anchor device or backing as specified or required in accordance with local building codes before wall is finished. Fasten concealed mounting flanges to anchor device or backing with at least two screws opposing each other in each flange. Snap flange covers over each mounting flange to conceal mounting screws. Concealed anchor devices and mounting screws are not included with Bobrick grab bars and must be specified as an accessory. For Grab Bars with an Intermediate Flange(s), Pull Snap-Flange Covers away from mounting flanges. Place grab bar in desired mounting location. Use intermediate flange as a template to mark location of mounting screws at intermediate flange only. Mark screw locations at the center of the slot in the middle of the double-keyhole shaped mounting holes (2) in the intermediate flange. Remove grab bar from wall. Drive the intermediate flange mounting screws into wall at marked locations. Note: Make sure to leave a space of just over 1/8'' (3.17mm) between the underside of the screw head and the wall. Install grab bar on the wall by placing the round ends of the intermediate flange double-keyhole shaped mounting holes over the mounting screws (2) are located in the middle of the flange slots. Install the mounting screws into the wall at the end flanges and secure tightly. Tighten the mounting screws at the intermediate flange. Press all snap-flange covers into place to conceal mounting flanges.

- Grab bar shall be type-304 stainless steel with satin-finish.
- Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/4" (32mm) outside diameter.
- Clearance between the grab bar and wall shall be 1-1/2" (38mm).
- Concealed mounting flanges shall be 11-gauge (3.2 mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with at least two screw holes for attachment to wall.
- Flange covers shall be 22-gauge (0.8mm) stainless steel, 3-1/4" (85mm) diameter, and shall snap over mounting flanges to conceal mounting screws and/or WingIt fasteners.
- Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit.
- Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.

B-5806.99x18 - 18" (455mm) long
​B-5806.99x24 - 24" (610mm) long
B-5806.99x30 - 30" (760mm) long
B-5806.99x36 - 36" (915mm) long
B-5806.99x42 - 42" (1065mm) long

Data sheet


Technische Daten:

  • Grab bar shall be type-304 stainless steel with satin-finish.
  • Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/4" (32mm) outside diameter.
  • Clearance between the grab bar and wall shall be 1-1/2" (38mm).
  • Concealed mounting flanges shall be 11-gauge (3.2 mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with at least two screw holes for attachment to wall.
  • Flange covers shall be 22-gauge (0.8mm) stainless steel, 3-1/4" (85mm) diameter, and shall snap over mounting flanges to conceal mounting screws and/or WingIt fasteners.
  • Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit.
  • Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.

Montage: Wandmontage
Materiaal: RVS
Sanitair inrichting: Handsteunen & Leuningen
Kleuren: Geborsteld RVS
Verdere links naar "Straight Bobrick grab bar peened of satin finish stainless steel in different legths"
Laatst bekeken