Beste Klanten & Zakelijke Partners!
Hartelijk welkom bij de Hygiene-shop.nl!
Op onze pagina actuele informatie houden wij u op de hoogte van alle nieuwtjes & actualiteiten.
Wij wensen iedereen gezondheid toe in deze aparte tijden!

B-5191 solid phenolic folding shower/dressing area seat for surface mounting

Compact design. Seat is constructed of durable, water-resistant, ivory colored, 5⁄16" (8mm) thick solid phenolic. Frame and mounting bracket are type 304 stainless steel and self-locking mechanism. Supports up to 500 lbs (227 kg) when properly installed. Seat 18" (455mm) wide, projects 15 13⁄16" (400mm) from wall.

Hoeveelheid Basisprijs
tot 1 € 427,13 * € 427,13 * / 1 Stuk(s)
vanaf 2 € 405,77 * € 405,77 * / 1 Stuk(s)
vanaf 4 € 392,96 * € 392,96 * / 1 Stuk(s)
vanaf 6 € 384,42 * € 384,42 * / 1 Stuk(s)
Inhoud: 1 Stuk(s)

Prijzen incl. btw excl. verzendingskosten

Levertijd in 6-11 werkdagen

Offerte aanvragen
  • BR000138
  • Bobrick
WebwinkelKeur Webwinkel Keurmerk
Bobrick B-5191 solid phenolic folding shower/dressing area seat load up to 204 kg Shower...meer
Productinformatie "B-5191 solid phenolic folding shower/dressing area seat for surface mounting"

Bobrick B-5191 solid phenolic folding shower/dressing area seat load up to 204 kg

Shower seat can be folded up against the wall when not in use. The spring at the top of baseplate locks seat into upright position until released by pulling the top of seat away from wall. Support system with guide bracket allows varying mounting heights and leaves floor clear for easier cleaning. Nonporous solid phenolic seat has slots to permit water to drain, does not splinter or require oiling, and will not support growth of bacteria. Slotless round-head carriage bolts and acorn nuts provide additional safety to user. Bobrick shower seats, when properly installed, have sufficient strength to support 500 lbs., (227 kg) complying with accessible design guidelines (including ADAAG in the U.S.A.).

Dimensions:
width: 455 mm
height: 400 mm
typical mounting height: 430 - 485 mm

Safety Plate is to be mounted on wall near Shower Seat in order to properly advise users of the Seat's weight restrictions. Correct installation of the Safety Plate will ensure that the Shower Seat meets A.N.S.I. Standards. Permanently affix Safety Plate to wall on either side of the Shower Seat at a minimum height of 30" (760mm). If mounted above Seat, the Plate must be high enough so that it is not covered when Seat is on the up position. Mounting screws (4) are recommended, but double-sided tape on rear of Plate may be used for very smooth, non-porous surfaces.

SAFETY WARNING: Shower seats are no stronger than the anchors and walls to which they are attached and must be firmly secured in order to support the loads for which they are intended. Consult and comply with local building codes. To avoid potential injury, the building owner or maintenance personnel should remove the shower seat from service if the shower seat is not adequately secured to the wall. Unit shall support static loads of up to 500 lbs (227 kg) when properly installed and used. To avoid potential seat malfunction, DO NOT use seat if weight exceeds 500 lbs (227 kg).

- Folding shower seat shall have a frame constructed of type-304, satin-finish stainless steel that consists of 16-gauge (1.6mm), 1-1/4'' (30mm) square tubing and 18-gauge (1.2mm), 1'' (25mm) diameter seamless tubing.
- Seat shall be one-piece, 5/16" (8mm) thick, solidly fused plastic laminate with matte-finish melamine surfaces, ivory-colored face sheets, and black phenolicresin core; secured to frame with stainless steel carriage bolts and acorn nuts.
- Shower seat shall be equipped with two 3'' (75mm) diameter mounting flanges constructed of type-304, 3/16'' (5mm) thick, satin-finish stainless steel; a guide bracket constructed of type-304, 16-gauge (1.6mm), satin-finish stainless steel; and a spring constructed of type-301, 24-gauge (0.6mm) stainless steel that is spot-welded to a baseplate of type-304, heavy-gauge stainless steel.
- Seat shall be able to lock in upright position when not in use.
- Shower seat shall comply with accessible design guidelines (including ADAAG in the U.S.A.).

Data sheet


Technische Daten:

  • Dimensions: width: 455 mm height: 400 mm
  • typical mounting height: 430 - 485 mm
  • Folding shower seat shall have a frame constructed of type-304, satin-finish stainless steel that consists of 16-gauge (1.6mm), 1-1/4'' (30mm) square tubing and 18-gauge (1.2mm), 1'' (25mm) diameter seamless tubing.
  • Seat shall be one-piece, 5/16" (8mm) thick, solidly fused plastic laminate with matte-finish melamine surfaces, ivory-colored face sheets, and black phenolicresin core; secured to frame with stainless steel carriage bolts and acorn nuts.
  • Shower seat shall be equipped with two 3'' (75mm) diameter mounting flanges constructed of type-304, 3/16'' (5mm) thick, satin-finish stainless steel; a guide bracket constructed of type-304, 16-gauge (1.6mm), satin-finish stainless steel; and a spring constructed of type-301, 24-gauge (0.6mm) stainless steel that is spot-welded to a baseplate of type-304, heavy-gauge stainless steel.
  • Seat shall be able to lock in upright position when not in use.
  • Shower seat shall comply with accessible design guidelines (including ADAAG in the U.S.A.).
     

Materiaal: Kunststof, RVS
Montage: Wandmontage, Wandmontage
Kleuren: Zilver
Meubels & Co: Stoelen
Sanitair inrichting: Douche stoel
Verdere links naar "B-5191 solid phenolic folding shower/dressing area seat for surface mounting"
Laatst bekeken